超微粉碎机厂家

咨询热线

13256798563

当前位置:河北快3开奖结果-新闻动态-行业新闻-超微粉碎机转子平衡性的影响因素有哪些?

neixin.png

超微粉碎机转子平衡性的影响因素有哪些?

超微粉碎机锤片的制造精度对超微粉碎机转子的平衡性影响很大。中药超微粉碎机厂一般要求转子上任意两组锤片之间的质量差不能超过5g。因此,锤片在加工过程中要严格控制精度,特别堆焊碳化钨锤片要严格保证堆焊工艺质量。
The manufacturing accuracy of hammer of ultra-fine crusher has a great influence on the balance of the rotor of ultra-fine crusher. The factory of ultra-fine crusher of traditional Chinese medicine generally requires that the quality difference between any two groups of hammers on the rotor should not exceed 5G. Therefore, the precision of hammer should be strictly controlled in the process of processing, and the quality of surfacing welding process should be strictly guaranteed, especially for tungsten carbide hammer.
锤片安装时应该每天安装成套的锤片,不允许套与套之间随意交换.锤片是粉碎机中直接打击物料的工作部件,因而也是磨损最快、更换最频繁的易损件.锤片的磨损指的是锤片工作角的磨损,锤片四个工作角磨损了,该锤片也就报废了.超微粉碎机锤片其形状、尺寸、排列方法、制造质量等,对粉碎效率和产品质量有很大影响.1.6mm比6.25mm锤片粉碎效果提高45%,比5mm提高25.4%.用薄锤片粉碎效率高,但使用寿命相对缩短.用多厚的锤片,应视粉碎对象和机型大小而异.
中药低温粉碎机
Hammers should be installed every day with complete sets of hammers, which are not allowed to be exchanged freely between sets. Hammers are the working parts of crushers that directly strike materials, and are therefore the most wearable and frequently replaced parts. Hammer wear refers to the wear of the working angles of hammers. Hammer wear refers to the wear of the four working angles of hammers, and the hammers will be scrapped. The shape, size, arrangement method and manufacturing quality of the hammer of ultra-fine crusher have great influence on the crushing efficiency and product quality. The crushing effect of 1.6 mm hammer is 45% higher than that of 6.25 mm hammer and 25.4% higher than that of 5 mm hammer. The crushing efficiency of thin hammer is high, but its service life is relatively shorter. The size of the object and type of the hammer with multiple thicknesses should be different.
中药超微粉碎机厂认为,锤片的排列方式最好达到下列要求:转子转动时,每块锤片的运动轨迹不重复;物料不会在锤片的推移下粉碎室内发生向一侧偏移的现象(特殊要求除外);转子受力平衡,高速运转时不产生振动.轴承过热轴承直接影响到到设备的正常运行及生产效率.
The factory of Chinese medicine ultrafine crusher considers that the arrangement of hammers is best to meet the following requirements: when the rotor rotates, the track of each hammer does not repeat; materials will not deviate to one side in the crushing chamber with the hammer moving (except for special requirements); the rotor is balanced, and there will be no vibration when running at high speed. The bearing is overheated and the bearing is straight. It affects the normal operation and production efficiency of the equipment.
设备运行过程中,使用者要特别注意轴承的升温和轴承部位的噪声,出现异常要及早处理.2个轴承座高低不平,或电机转子与粉碎机转子不同心,会使轴承受到额外负荷的冲击,从而引起轴承过热.出现这种情况,要马上停机排除故障,以避免轴承早期损坏.轴承内润滑油过多、过少或老化也是引起轴承过热而损坏的主要原因.
During the operation of the equipment, the users should pay special attention to the heating of the bearing and the noise of the bearing parts, and deal with the abnormalities as soon as possible. The uneven two bearing seats, or the centrifugal rotor of the motor and the crusher, will cause the bearing to be impacted by the additional load, thus causing the bearing to overheat. In this case, the machine should be stopped immediately to eliminate the fault. Avoid early damage of bearings. Excessive, too little or aging lubricant in bearings is also the main cause of Bearing Overheating and damage.
因此,中药超微粉碎机厂建议要按着使用使用书要求按时定量地加注润滑油,一般润滑占轴承空间的70%-80%,过多或过少都不利于轴承润滑和热传递.轴承延长其使用寿命.轴承盖与轴的配合过紧,轴承与轴的配合过紧或过松都会引轴承过热.一但发生这种问题,在设备运转中,就会发出磨擦声响及明显的摆动.​
Therefore, it is suggested that lubricating oil should be added on time and quantitatively according to the requirements of the use book. Generally, lubrication accounts for 70-80% of the bearing space. Too much or too little lubrication is not conducive to bearing lubrication and heat transfer. Bearing prolongs its service life. Too tight coordination between bearing cover and shaft, too tight or too loose coordination between bearing and shaft will lead to bearing. Overheating. Once this problem occurs, the friction noise and obvious oscillation will be emitted during the operation of the equipment.
感谢您的阅读与观看,本文的精彩内容来自:中药低温粉碎机我们会有更多的精彩内容继续为您呈现,详情请点击:http://www.69gege.com
Thank you for your reading and watching. The wonderful content of this article comes from: Chinese medicine cryogenic crusher, we will have more wonderful content to continue to show you. For more details, please click: http://www.69gege.com.

济南骏程机械设备河北快3开奖结果

PHONE

13256798563 / 400-766-9788 

E-mail

junchengweifen@163。com

ADDRESS

济南市市中区袁庄会龙工业园

Website

http://www.69gege.com

  • 手机客户端
  • 客服微信

河北快3开奖结果 / 关于我们 / 产品中心 / 工程案例 / 新闻动态 / 服务和支持 / 联系我们 /

版权所有:济南骏程机械设备河北快3开奖结果 备案号: 鲁ICP备15034461号-3 技术支持:  网站地图 XML TXT 流量统计:

博美彩票APP下载 爱购彩票APP 爱拼彩票平台 河北快3走势图 泊利彩票平台 必博彩票APP下载 爱乐彩票平台 河北快3开奖直播 河北快3走势图 宝赢彩票APP下载