超微粉碎机厂家

咨询热线

13256798563

当前位置:河北快3开奖结果-新闻动态-骏程百科-中药超细粉碎机操作需要哪些事项?

neixin.png

中药超细粉碎机操作需要哪些事项?

1、中药超细粉碎机起动前,先用手转动转子,查看一下齿爪、锤片及转子运转是否灵活可靠,破碎室内有无磕碰现象,转子的旋转方向是否与机箭头所指方向共同,动力机及塑料破碎机润滑是否杰出。
1. Before starting the ultra-fine crusher of traditional Chinese medicine, first rotate the rotor by hand to check whether the grippers, hammers and rotors operate flexibly and reliably, whether there is knocking in the crushing room, whether the rotating direction of the rotor is in line with the direction indicated by the arrow, and whether the lubrication of the power and plastic crusher is outstanding.
2、作业中要随时留意中药超细粉碎机的运转情况,首先,送料要均匀,以防阻塞碎料室;其次,不要长时间超负荷作业。若发现有振荡、杂音、轴承与机体温度过高,向外喷料等现象,应立即停机查看,排除故障后方可继续作业。
2. Always pay attention to the operation of the ultra-fine crusher of traditional Chinese medicine in operation. First, the feed should be uniform to prevent blocking the crushing chamber. Second, do not overload the operation for a long time. If it is found that there are oscillation, noise, high temperature of bearing and body, and spraying material outward, it is necessary to stop the machine immediately to check, and the operation can be continued after troubleshooting.
3、中药超细粉碎机与动力机组要装置结实。若需要塑料破碎机长时间固定作业,应将其固定在水泥基础上;若需要塑料破碎机流动作业,机组应装置在用角铁制成的机座上,而且保证动力机和塑料破碎机的皮带轮槽处于同一回转平面。
中药超细粉碎机
 
3. The main devices of the ultra-fine crusher and power unit of Chinese medicine are strong. If the plastic crusher needs to be fixed for a long time, it should be fixed on the cement foundation; if the plastic crusher needs to be mobile, the unit should be installed on the seat made of angle iron, and ensure that the power machine and the belt groove of the plastic crusher are in the same rotary plane.
4、中药超细粉碎机起动后应保持其先空转3min,没有异常现象后再投料作业。且不要随意更换皮带轮,以防转速太高致使破碎室,或转速太低影响粉碎机的作业效率。
4. After starting, the ultra-fine crusher of traditional Chinese medicine should keep it idling for 3 minutes, without abnormal phenomena before feeding. And don't change the pulley at will, in order to prevent the breaking room caused by too high speed or too low speed affecting the operation efficiency of the crusher.
5、中药超细粉碎机装置完后要查看各部紧固件的紧固情况,若有松动要给予以拧紧。同时要查看皮带松紧度是否适宜。中药超细粉碎机阻塞的办法:
5. After the device of Chinese medicine superfine crusher is finished, the fasteners of each part should be checked and tightened if loosening occurs. At the same time, check the belt tightness is appropriate. The method of blocking the ultra-fine crusher of traditional Chinese medicine:
1、进料速度过快,负荷增大,造成阻塞。在进料过程中,要随时留意电流表指针偏转角度大,如果超越额定电流,表明电机超载,长时间过载,会烧坏电机。出现这种情况应立即减小或关闭料门,也可以改变进料的方法,经过增加喂料器来操控进料量。喂料器有手动、自动两种,用户应根据实际情况选择适宜的喂料器。由于粉碎机转速高、负荷大,而且负荷的波动性较强。所以,中药超细粉碎机作业时的电流一般操控在额定电流的85%左右。
1. The feeding speed is too fast, and the load increases, resulting in blockage. In the process of feeding, we should always pay attention to the large deflection angle of the ammeter pointer. If the current exceeds the rated current, it indicates that the motor is overloaded and overloaded for a long time, it will burn the motor. When this happens, the feeding gate should be reduced or closed immediately, or the feeding method can be changed, and the feeding quantity can be controlled by increasing the feeder. There are two kinds of feeders: manual feeder and automatic feeder. Users should choose the appropriate feeder according to the actual situation. Because of the high speed, high load and strong fluctuation of the load of the crusher. Therefore, the current of the ultra-fine crusher of traditional Chinese medicine is generally controlled at about 85% of the rated current.
2、出料管道不畅或阻塞进料过快,会使粉碎机风口阻塞;与运送设备匹配不妥会造成出料管道风减弱或无风后堵死。查出故障后,应先清通送口变更不匹配的运送设备,调整进进料量,使设备正常运行。
2. Imperfect discharge pipeline or blocked feeding too fast will block the pulverizer tuyere; improper matching with transport equipment will cause the air of discharge pipeline to weaken or block up after no air. After finding out the faults, the unmatched conveying equipment should be cleared through the feeding port, and the feeding quantity should be adjusted to make the equipment run normally.
本文由中药超细粉碎机提供技术支持,更多的详细精彩内容请点击我们的官方网站http://www.69gege.com,我们将会全心全意为您提供满意的服务。
This article is supported by TCM superfine grinder. For more details, please click on our official website http://www.69gege.com. We will provide you with satisfactory service wholeheartedly.

济南骏程机械设备河北快3开奖结果

PHONE

13256798563 / 400-766-9788 

E-mail

junchengweifen@163。com

ADDRESS

济南市市中区袁庄会龙工业园

Website

http://www.69gege.com

  • 手机客户端
  • 客服微信

河北快3开奖结果 / 关于我们 / 产品中心 / 工程案例 / 新闻动态 / 服务和支持 / 联系我们 /

版权所有:济南骏程机械设备河北快3开奖结果 备案号: 鲁ICP备15034461号-3 技术支持:  网站地图 XML TXT 流量统计:

河北快3走势图 河北快3走势图 河北快3开奖直播 伯爵彩票APP下载 河北快3走势图 必中彩票APP下载 河北快3开奖直播 百万彩票APP 河北快3走势图 博亿彩票APP下载